[kepler-dev] Once Again Issues in buidling kepler 2.0

[AMARNATH, Balachandar]

Dear David Welker,
 
 Thanks for the repply. I still encounter the issue.I ran the exactly
the same commands.
 
 
***************************** 
[change-to] ptolemy revision:57640 
[change-to] svn co -r57640
svn://source.eecs.berkeley.edu/chess/ptII/branches/rel-8-0-beta-2
c:\Home\BAAMARNA5617\kepler-2.0\MyModules\ptolemy-8.0\src
[change-to] svn: Unknown hostname 'source.eecs.berkeley.edu'
[change-to]

BUILD FAILED 
ERROR: It appears that the command did not execute properly and exited
with an exit code of: 1 
****************************************** 

 

Any hint to come out of the issue ? 

regards
Balachandar


  _____  

	From: David Welker [mailto:david.v.welker at gmail.com] 
	Sent: 23 April 2010 12:27
	To: AMARNATH, Balachandar
	Subject: Re: [kepler-dev] Again Issues in buidling kepler 2.0
	
	
	Hi  Balachandar, 

	This looks like a network problem. We use the svn protocol for
ptolemy because using other protocols causes certain issues to arise.
Using this protocol is not a problem.

	I would suggest you try the command again. It should work.
Sometimes with partial downloads, issuing the command again can cause
issues that can be resolved by deleting <kepler.modules> ptolemy to
start clean, but it usually works without doing that.

	-David


	On Apr 22, 2010, at 11:03 PM, AMARNATH, Balachandar wrote:





		Dear All, 

		I could write an actor and instantiate in kepler 1.0 but
the same is not working with kepler 2.0 (I installed kepler 2.0 using
<kepler>.jar version).

		I am trying to write a simple actor using Kepler 2.0. I
was advised by the documentation to build the kepler from svn and use to
develop the actor. 

		So, I again, I ran the following command 

		>  svn co
https://code.kepler-project.org/code/kepler/branches/releases/release-br
anches/build-area-2.0
<https://code.kepler-project.org/code/kepler/branches/releases/release-b
ranches/build-area-2.0>  build-area 
		>  cd cd build-area 
		>  ant change-to -Dsuite=kepler-2.0 

		But it ran for sometime and finally end up with error.
The last few stack trace is given below 


		***************************** 
		[change-to] ptolemy revision:57640 
		[change-to] svn co -r57640
svn://source.eecs.berkeley.edu/chess/ptII/branches/rel-8-0-beta-2
c:\Home\BAAMARNA5617\kepler-2.0\MyModules\ptolemy-8.0\src

		[change-to] 

		BUILD FAILED 
		ERROR: It appears that the command did not execute
properly and exited with an exit code of: 1 
		****************************************** 

		Is this because of the svn protocol it uses to connect
to the berkey.edu server ? Is it possible to connect with 'https'

		Can anyone help me out ? 


		With thanks and regards 
		Balachandar 



		The information in this e-mail is confidential. The
contents may not be disclosed or used by anyone other than the
addressee. Access to this e-mail by anyone else is unauthorised.
		If you are not the intended recipient, please notify
Airbus immediately and delete this e-mail.
		Airbus cannot accept any responsibility for the accuracy
or completeness of this e-mail as it has been sent over public networks.
If you have any concerns over the content of this message or its
Accuracy or Integrity, please contact Airbus immediately.
		All outgoing e-mails from Airbus are checked using
regularly updated virus scanning software but you should take whatever
measures you deem to be appropriate to ensure that this message and any
attachments are virus free.
		_______________________________________________
		Kepler-dev mailing list
		Kepler-dev at kepler-project.org
	
http://mercury.nceas.ucsb.edu/kepler/mailman/listinfo/kepler-dev
		


	This mail has originated outside your organization, either from
an external partner or the Global Internet.
	Keep this in mind if you answer this message.
	


The information in this e-mail is confidential. The contents may not be disclosed or used by anyone other than the addressee. Access to this e-mail by anyone else is unauthorised.
If you are not the intended recipient, please notify Airbus immediately and delete this e-mail.
Airbus cannot accept any responsibility for the accuracy or completeness of this e-mail as it has been sent over public networks. If you have any concerns over the content of this message or its Accuracy or Integrity, please contact Airbus immediately.
All outgoing e-mails from Airbus are checked using regularly updated virus scanning software but you should take whatever measures you deem to be appropriate to ensure that this message and any attachments are virus free.

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mercury.nceas.ucsb.edu/kepler/pipermail/kepler-dev/attachments/20100423/2d8610a3/attachment-0001.html>